No results were found for the filter!
Recommended
Art.-Nr. 1162037
bsCylinder head gasket For engine type 125 (recognisable by a larger gap between cylinder 2 and 3) 1400/1600 (piston diameter 80mm). Special production reinforced for engine type: 124AC000,124C000,125A000, 125B00 Thickness: 1,7 mm
€184.95 *
Art.-Nr. 1162040
Thickness: 1.7mm We highly recommend ordering the reinforced cylinder head gasket (item no. 1162043) and installing it instead of this standard gasket! The reinforced seal can withstand higher pressure, is thermally more resilient and...
€23.95 *
Art.-Nr. 1164078g
Offered is a used lower housing for an intake manifold injector without injector.
€129.95 *
Art.-Nr. 1164080g
Offered is a complete intake manifold without injector spider without throttle switch.
€299.95 *
Art.-Nr. 1164081
The seal has only one water bore in the outer area
€8.95 *
Art.-Nr. 1164084
From AS 2. series
€6.95 *
Art.-Nr. 1164086
Seal with connection for exhaust gas recirculation
€8.95 *
Art.-Nr. 1162087
Screw V-belt pulley crankshaft from year of manufacture '83. Since this screw has a left-hand thread and can practically not come loose, it is fixed with a maximum of 80 Nm! M14 x 55 x 1,5 Width across flats 22mm
€16.99 *
Art.-Nr. 1162091
Bearing shell set 1st oversize - 0.254mm Engine type 124/125 1400/1600 Fiat 124 Sport AC/AS Fiat 124 Sport BC/BS Fiat 125 - Fiat 125 S Fiat X 1/9 1300
€54.95 *
Art.-Nr. 1162097
Standard, set (8 pieces) 1800/2000 engine (front crankshaft with pulley for several belts)
€49.95 *
Art.-Nr. 1162098
1. oversize - 0,254 mm, set (8 pieces) engine type 123 1800/2000ccm ( pulley on crankshaft for several belts )
€85.95 *
Art.-Nr. 1162099
€39.95 *
Art.-Nr. 1162100
Set of thrust washers for crankshaft (1st oversize) For engines with 1438 cc and 1608 cc displacement.
€49.95 *
Art.-Nr. 1162115
With inner diameter 29 mm
€55.95 *
Art.-Nr. 1162116
Made of metal Inner diameter 30 mm
€56.95 *
Art.-Nr. 1162117
Camshaft sprocket inlet with rear leading edge for toothed belt
€49.95 *
Art.-Nr. 1162121
€69.95 *
Art.-Nr. 1162129
With marking for toothed belt setting 79-85 (straight tips)
€54.95 *
Art.-Nr. 1164073
Vane pump incl. mounting material can be used for Fiat 124 Spider up to year of construction 79. Attention: If your pump is defective, be sure to check whether there is rust or other impurities in your tank, as the fuel is only cleaned...
€49.95 *
Art.-Nr. 1164066
Fiat 124 Coupe/Spider 1400 as of 07/1967 Mechanical fuel pump for AS 1400 carburettor models. With long lever (63 mm, measured from flange).
€36.95 *
Art.-Nr. 1164070
2x seals article no.: 1162133 are required for assembly.
€9.95 *
Art.-Nr. 1164065
Mechanical fuel pump for CS2 2000 carburettor models. Alternatively electric fuel pump for carburettor models Art. No. 1164073 Advantage: Fuel is always immediately available at the carburettor and the annoying "georgele" until fuel...
€42.95 *
Art.-Nr. 1162143
Oil pump with short splines for drive Up to chassis no.: 152387 Please note before purchasing: Check the wrench size of the nut/bolt at the front of the crankshaft pulley. If you have a 38 mm wrench size (right-hand thread nut), you need...
€139.95 *
Art.-Nr. 1162145
Oil pump with long splines, oil pump drive Note before purchasing: Check the wrench size of the nut/bolt at the front of the crankshaft pulley. If you have a 38 mm wrench size (right-hand thread nut), you need the oil pump with item...
€229.95 *
Recently Viewed