• Secure Payment
  • Fast Shipping
  • Free Returns with PayPal ¹

Repair panel for wheel arch rear right 103mm height Fiat 124 Spider

€59.00 *

incl. VAT and plus Shipping

Delivery time 4-7 workdays

  • 1110140
  • 50800, 2064592, 1112024
  • Replication
  • 1
Product information "Repair panel for wheel arch rear right 103mm height Fiat 124 Spider"

For the right side in the direction of travel.

Category: Reparaturbleche
Related Links
Customer evaluation for "Repair panel for wheel arch rear right 103mm height Fiat 124 Spider"
Write an evaluation
Evaluations will be activated after verification.

The fields marked with * are required.

Manufacturer Model Type
FIAT 124 Spider
AS (1400)
BS (1400)
BS1 (1600)
CS (1600)
CSA (1800)
CS1 (1800)
CS2 (2000)
CS0 (2000)
DS (2000)
VX (2000)

If not, the original wheel arch in the vehicle, this part is used, the wheel arch is have already been replaced, Article Nr.1112027 be ordered.

In most cases in the US models and in some cases also Euro spidering is the outer wheel housing Article No.: 1110083 In the contact area with the wheel arch and slightly higher in the arched reinforcement (only heavily rusted in US models) since original color or never wax was introduced at this point. Here you should be sure to replace both parts in order to achieve a permanent repair.

We will in the body in such a case only the wheel arch on the side panel Marks (so that you can then guarantee a perfect fit) then cut the wheel arch as far as necessary. Now the outer wheel well, if not caused by rust affected up to 3 cm in front of Verbindungsfals to the inner wheel arch. Then the wheel arch is adjusted deposed the side part with an offsetting pliers. Both contact surfaces are made metallic blank and treated with spot weld primer, both parts are now connected by spot welding together. Now the new wheel arch is adjusted. Before it is used, tinning we make the transition from wheel arch to the side part to here a metal interconnect. Wheel arch and wheel well will now be primed in the region of the later is no longer accessible once and anschießend the junction of the wheel arch and the side part is provided with paint, we additionally now with a sealing Pu sealed. Contact point to the wheel arch and wheel well of new wheel well to wheel well old will now be made bare metal (in the width of 1 cm) now points of contact welding point primer is applied to the bare and the wheel house used by spot welding (as original). The crossing points will now be painted again in two steps. In the wheel Pu Sealant is additionally applied during the transition. After painting the vehicle / side part underbody protection is introduced into the wheel house from the inside of the wheel arch and is flooded or with wax. After the treatment we have to date not make the wheel arch with renewed rust had.

Floor pan left Fiat 124 Spider 66-85 Floor pan left Fiat 124 Spider 66-85
Art.-Nr. 1110148
€129.00 *
Mounting bracket grid below Mounting bracket grid below
Art.-Nr. 1124020
€4.50 *
On A Diet For A Month magnet 8x6cm On A Diet For A Month magnet 8x6cm
Art.-Nr. 1091006
€1.30 * €1.90 *
Route 66 Red Car plate postcard 14x10cm Route 66 Red Car plate postcard 14x10cm
Art.-Nr. 1091001
€1.90 * €2.95 *
Hex nut M12x1,25 galvanized Hex nut M12x1,25 galvanized
Art.-Nr. 1090022
€0.35 *
Spark Plug FIAT 124 Spider / Coupe Spark Plug FIAT 124 Spider / Coupe
Art.-Nr. 1184051
€3.40 *
Viewed